Willkommen, Gast
Benutzername: Passwort: Angemeldet bleiben:
  • Seite:
  • 1
  • 2

THEMA:

Segelflug - launch 15 Okt 2017 14:01 #1

  • Bose
  • Boses Avatar Autor
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Beiträge: 28
  • Dank erhalten: 0
Hello all - I use a DC 24 TX - trying to set up a launch phase where the elevator function is delayed by 3seconds after launch.
I use a switch with 3 pos. 1) switch Down = motor stop 2) switch mid = motor half speed 3) switch up = motor full speed + ailerons and flaps up by 2 mm + elevator is Down by 2mm. All is working OK. But I Want to delay the Down movement of the elevator by 3 SECONDS. How do I do this?

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Segelflug - launch 23 Okt 2017 20:27 #2

  • Bose
  • Boses Avatar Autor
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Beiträge: 28
  • Dank erhalten: 0
Antwort auf Deutsch ist OK

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Segelflug - launch 25 Okt 2017 20:52 #3

  • qwertz
  • qwertzs Avatar
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Beiträge: 25
  • Dank erhalten: 9
Do you want to delay the down function one time during activating for 3 seconds?
Meaning the elevator shall go down to an selected position with a delay of 3 seconds as new base position?

Regards Bodo

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Letzte Änderung: von qwertz.

Segelflug - launch 25 Okt 2017 21:38 #4

  • qwertz
  • qwertzs Avatar
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Beiträge: 25
  • Dank erhalten: 9
If I do get you right, do as followed:

Define a flight phase for your elevator function and adjust a delay of 3 seconds in the menu.
Define a mixer from elevator to elevator and set it to (S) Selected.
If the elevator down flight phase is active, select a constant curve and a master value.
With adjustment of these two parameter you can put the elevator down to the required position.

If the flight phase is activated, the base position will change to the new defined position by time, meaning the servo will go down to the new base position step by step over the 3 seconds.
I hope I was able to help you so far and got you right.

Regards Bodo
Folgende Benutzer bedankten sich: Bose

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Letzte Änderung: von qwertz.

Segelflug - launch 25 Okt 2017 23:44 #5

  • Bose
  • Boses Avatar Autor
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Beiträge: 28
  • Dank erhalten: 0
Thank you very much Bodo for your help.
The reason for delaying the Down movement of the elevator is to prevent the model from pointing down immediately after launch.
I do not know if it is 3 seconds or less - I had to put some value so that I Can explain my problem better.
If you have a better method for the launch phase for a powered glider (F5J introduction) then I Will welcome your suggestions.
Thank you - Bose

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Segelflug - launch 25 Okt 2017 23:45 #6

  • Bose
  • Boses Avatar Autor
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Beiträge: 28
  • Dank erhalten: 0
Thank you very much Bodo for your help.
The reason for delaying the Down movement of the elevator is to prevent the model from pointing down immediately after launch.
I do not know if it is 3 seconds or less - I had to put some value so that I Can explain my problem better.
If you have a better method for the launch phase for a powered glider (F5J introduction) then I Will welcome your suggestions.
Thank you - Bose

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Seite:
  • 1
  • 2
Ladezeit der Seite: 0.244 Sekunden
Powered by Kunena Forum