Willkommen, Gast
Benutzername: Passwort: Angemeldet bleiben:
  • Seite:
  • 1
  • 2
  • 3

THEMA:

Ditex 0807W do not want start working time to time 04 Nov 2017 23:19 #1

  • HSC
  • HSCs Avatar Autor
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Beiträge: 34
  • Dank erhalten: 23
Hello Everybodey !

Subject Ditex 0807W

Yestrday I have set the travels on the bench on my Salto wings.....

Anyway when I disconect the power and turn it on again ( CB 200, Jeti Lion 8,4V and RC swich), one servo in the wing did not want start working ( simply did not want to make initialization with two beeps), did not have noo sign of life, actualy i was abele too turn ailerns by my hend...

The fact is, the servo was pretty much loaded, but not blocked minutes before and I was get temparature warning....

Doo you ting is this behaviour have any conection with thermal ower heating ?

Imidiamty after that I reestarted hole plane and again the same storry......

After that I turn off the system for minute and servo start too work normaly , later I was try too replicate the problem 20 times but servo work normaly...

Anbodey have an idea what went wrong...plese shear it

Now I will have full throusers of shit flying this plane with this servo :unsure: :unsure: :unsure:

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Ditex 0807W do not want start working time to time 05 Nov 2017 08:47 #2

  • WalterL
  • WalterLs Avatar
  • Offline
  • Platinum Boarder
  • Platinum Boarder
  • Beiträge: 784
  • Dank erhalten: 304
May be that's the reason it isn't available anymore.
I would try to reprogram it and add the newest firmware. I own six pieces of that servo and updated all of them. They work perfect but I didn't have any overloads so far.

Regards and good luck,
Walter

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Ditex 0807W do not want start working time to time 05 Nov 2017 18:46 #3

  • HSC
  • HSCs Avatar Autor
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Beiträge: 34
  • Dank erhalten: 23
I hope this is not the reason for out of stock...
I have 8 of them in this bird :unsure:
Also I have addressed question directly too hacker, I hope I will get some response from them now....
If I get some info I will report
Regards

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Ditex 0807W do not want start working time to time 08 Nov 2017 10:30 #4

  • HSC
  • HSCs Avatar Autor
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Beiträge: 34
  • Dank erhalten: 23
Hello !

Still noo response from Hacker:angry: ...

At least they could say " wee do not know what is the problem, wee are working on it..."

Regards

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Ditex 0807W do not want start working time to time 08 Nov 2017 10:51 #5

  • PW
  • PWs Avatar
  • Offline
  • Moderator
  • Moderator
  • Beiträge: 9322
  • Dank erhalten: 3504
Hi,

you can telefone Hacker nearly every day (Monday- Friday)... one telefone call

Regards
PW
Rechtsbeistand u.a. bei "Modellflugproblemen"etc. : Rechtsanwälte Wessels & Partner, Tel.: 02362/27065

PW Modellbautechnik ( Jeti Kombiangebote, Beratung/Einstellservice etc.)

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Letzte Änderung: von PW.

Ditex 0807W do not want start working time to time 09 Nov 2017 13:11 #6

  • HSC
  • HSCs Avatar Autor
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Beiträge: 34
  • Dank erhalten: 23
Hello to all !

Well, I have actualy call too the Hacker company yesterday in the afternoon...

Verry nice man talk too mee and give mee some good anwsers ( Uffff I forgt his name ) :

Hee say noo referncing after swich on, could have relation with ower heating ( signal in previous sesion), but it is a bit strange, usualy Ditex servo reduce torque if overheating is present...

Anyway I must send servo back too Hacker and they will check the servo on the aparatures if everything is ok.

Wee have also speak about ditex SW from jeti, shold bee ready in few weeks for Rex recivers, for CB a litle bit later...

Thanx for the help, regards:)

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Letzte Änderung: von HSC.
  • Seite:
  • 1
  • 2
  • 3
Ladezeit der Seite: 0.227 Sekunden
Powered by Kunena Forum