Please implement value sequence based alarms

  • onki
  • onki's Avatar Offline Autor
  • Platinum Mitglied
  • Platinum Mitglied
  • Beiträge: 2286
  • Dank erhalten: 791

Please implement value sequence based alarms wurde erstellt von onki

Posted 18 Okt. 2014 09:39 #1
Hi,

The alarm feature is nice but I think there is something missing.
It is only possible to define alarms by logic operators (X=Y;X>Y;X<Y) and for the vario a time sequence can be used.
But many parameters would be easier to hande if a "value sequence" can be defined.
Just some examples:
  • Height every 50m
  • Capacity every 500mAh
  • RX-Voltage every 0.1V
  • Fuel level every 200ml
I think there are many applicataions using this way of telemetry alarms. It can be done (limited using the current firmware version but it takes a lot of alarms to be programmed and in some cases the amount of available alarm entries are just not enough.
So please add value sequence based alarm to make using the alarms even easier.

Best regards
Onki
Gruß aus dem Nordschwarzwald
Rainer aka Onki
www.onki.de
gepostet unter Verwendung von 100% recycelter Elektronen.
von onki
Folgende Benutzer bedankten sich: sunbeam, ***EX, Günter, Ba-Nause, Donskills

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • ***EX
  • ***EX's Avatar Offline
  • Gebannt
  • Gebannt
  • Beiträge: 4974
  • Dank erhalten: 2410

***EX antwortete auf Please implement value sequence based alarms

Posted 18 Okt. 2014 11:18 #2
Hi Martin,

Onki means that the alarm needs an extra option step size.
A start value 500 mah for example and a step size 200.
Result are alarms 500,700,900,1100...mah.

A better idea is a selectable JSN File witch include all alarms that you need for the model.
With a new model I need only select the JSN file again and all needed alarms work again.
Then you can make template JSN files for each model type.(glider, F3A-models...)
Maybe alarm1.jsn,alarm2.jsn,alarm3.jsn like the selectable timer type speak, peep1 and peep2.

With greets
Harald
Last Edit:18 Okt. 2014 11:36 von ***EX
Letzte Änderung: 18 Okt. 2014 11:36 von ***EX.
Folgende Benutzer bedankten sich: Donskills

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Heli-Snoopy
  • Heli-Snoopy's Avatar Offline
  • Premium Mitglied
  • Premium Mitglied
  • Beiträge: 113
  • Dank erhalten: 27

Heli-Snoopy antwortete auf Please implement value sequence based alarms

Posted 20 Okt. 2014 19:34 #3
And Alarm delay.
Example:
If you monitor flight Aku X < 41 V and with a hard pitch pump the Volt goes short time under 41V and beck to 42V, alarm is activated. If you could set a delay you could balance out the short minus peek.

Thanks for your effort.
Gruss Hansi
______________________
portal.heli-snoopy.ch
von Heli-Snoopy

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Ladezeit der Seite: 1.005 Sekunden