rate of change output on sticks

  • ruud
  • ruud's Avatar Offline Autor
  • Neues Mitglied
  • Neues Mitglied
  • Beiträge: 4
  • Dank erhalten: 0

rate of change output on sticks wurde erstellt von ruud

Posted 23 Nov. 2014 12:00 #1
I think the rate of change of the stick is a ferry important input for mixers.
So you can setup a mixer from 'throttle rate of change' to 'aileron' to compensate motor torque.
With the idea that is you throttle up slowly there is almost no aileron compensation. and if you do it quickly there is more compensation.
And if the stick is on one position there is no compensation.

Is this a possibility in the current software for the DS-16 transmitter?
And if it's not can it be made in the next firmware?

Regards
Ruud
Last Edit:23 Nov. 2014 12:01 von ruud
Letzte Änderung: 23 Nov. 2014 12:01 von ruud.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • dibub
  • dibub's Avatar Offline
  • Elite Mitglied
  • Elite Mitglied
  • Beiträge: 222
  • Dank erhalten: 33

dibub antwortete auf rate of change output on sticks

Posted 23 Nov. 2014 13:19 #2
Dear Ruud,

it is not in the current software and I doubt it will be easy to implement (or to understand for most users).

I think if you need functionality like that, you should go for the Assist or any other gyro system. These would not need fine tuning, I think a change rate mixing to other functions would not be easy to adjust anyway. Taking your example, the mixing also would be dependant on the actual slope (climbing, descending, flighing upside down ...).

I think you would do more bad than that it would help. And at the end of the dayit is your job to fligh ;) ;) ;) .

Best regards

Dirk
von dibub

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • PW
  • PW's Avatar Offline
  • Moderator
  • Moderator
  • Beiträge: 9680
  • Dank erhalten: 3806

PW antwortete auf rate of change output on sticks

Posted 23 Nov. 2014 13:41 #3
Hi,

not in the actuall software and not planed !


Regards

PW
Rechtsbeistand u.a. bei "Modellflugproblemen"etc. : Rechtsanwälte Wessels & Partner, Tel.: 02362/27065

PW Modellbautechnik ( Jeti Kombiangebote, Beratung/Einstellservice etc.)
von PW

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • ***EX
  • ***EX's Avatar Offline
  • Gebannt
  • Gebannt
  • Beiträge: 4974
  • Dank erhalten: 2410

***EX antwortete auf rate of change output on sticks

Posted 23 Nov. 2014 20:44 #4
Hallo Ruud,
Make a bridge between PPM-In and PPM-OUT PIN of your DS-16 and make a new funkction with the throttle stick and channel 8 with a
individual function curve. Use the Switch CH8 for the mixer and it works fine.

With greets
Harald
Last Edit:23 Nov. 2014 20:46 von ***EX
Letzte Änderung: 23 Nov. 2014 20:46 von ***EX.
Folgende Benutzer bedankten sich: PW

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • ruud
  • ruud's Avatar Offline Autor
  • Neues Mitglied
  • Neues Mitglied
  • Beiträge: 4
  • Dank erhalten: 0

ruud antwortete auf rate of change output on sticks

Posted 24 Nov. 2014 10:40 #5
Thanks for the comments.

I Understand it will be a hard thing to use and implement for most users.
So I can understand that it is not in the planning for a software update.

@Harald
I don't fully understand what You achieve. Can You explain it some more because it sounds interesting.

Thanks in advance
Ruud.
von ruud

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • ***EX
  • ***EX's Avatar Offline
  • Gebannt
  • Gebannt
  • Beiträge: 4974
  • Dank erhalten: 2410

***EX antwortete auf rate of change output on sticks

Posted 24 Nov. 2014 10:56 #6
With a Bridge of the PPM-IN and PPM-OUT PIn you can give the Switch of a mixer an individual function curve.
Even the switch of the Butterfly mixer get an function curve and you can change the function curve with additional mixer in the air too.

With greets
Harald.
von ***EX

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Ladezeit der Seite: 0.995 Sekunden