CB200 & RSAT

  • Didier
  • Didier's Avatar Offline Autor
  • Junior Mitglied
  • Junior Mitglied
  • Beiträge: 38
  • Dank erhalten: 2

CB200 & RSAT wurde erstellt von Didier

Posted 28 Feb. 2016 15:30 #1
Hey guys,

Question 1:
I set-up a CB200 with 2x RSAT's on the latest software on all.
If I check the manual and youtube, you have to set the RSAT on "EX" in device explorer.
But in device explorer you only can select "EX & PPM positeve".
The system works on this settings but I wonder if the RSAT/CB200 use the EX or PPM protocol?

Question 2:
In device explorer RSAT1 is on top off the screen, followed by CB200 and then RSAT2. Is this correct?
If I check youtube and several screenshots, you always sees CB200 after the second RSAT in device explores. Both RSAT's have the same settings and they seems connected to the CB200.

Thanks guys!



didier is online now Send a private message to didier Find More Posts by didier
von Didier

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • PW
  • PW's Avatar Offline
  • Moderator
  • Moderator
  • Beiträge: 9680
  • Dank erhalten: 3806

PW antwortete auf CB200 & RSAT

Posted 28 Feb. 2016 15:44 #2
Hi Didier,

everything OK ! B) Plug cable in EXT port of RSats .


Regards
PW
Rechtsbeistand u.a. bei "Modellflugproblemen"etc. : Rechtsanwälte Wessels & Partner, Tel.: 02362/27065

PW Modellbautechnik ( Jeti Kombiangebote, Beratung/Einstellservice etc.)
Last Edit:28 Feb. 2016 15:58 von PW
Letzte Änderung: 28 Feb. 2016 15:58 von PW.
Folgende Benutzer bedankten sich: Didier

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Didier
  • Didier's Avatar Offline Autor
  • Junior Mitglied
  • Junior Mitglied
  • Beiträge: 38
  • Dank erhalten: 2

Didier antwortete auf CB200 & RSAT

Posted 03 März 2016 10:30 #3
Danke PW! :)


I have a "minor" problem though, maybe you has a clue what it could be.

I set-up my Ultra Flash with a Central box 200 (latest 24ch SW) and 2 Rsat RX (latest 24ch SW).
Pin EX1, pin 14 and pin 15 set to “telemtry input”.
All works very good but I have some minor telemetry problems.
I hook up a PB GPS 2, JJXC-EX (Jetcat telemetry) and Jeti Mbar on the above mentioned pins.
Total telemetry inputs is 25 including the telemetry of the CB200. (25 is the nummer in "sensor/logging menu")
The Mbar is "visual" in device explores.
The problems is that the value of the MBAR (pressure and temperature) are sometimes on and off on the DS-16 display. This happens a couple of times per minute but there is no pattern regarding time interval. The JJXC generates 6 parameters and 2 of them have a little bit the same issue. (Fuel left, ECU voltage)
You can see in "device explorer" that the Mbar is connected/disconnected. (check mark/cross repeatedly )
I already swapped the sensors between port and also replaced patch cables but this doesn’t seems the problem.
I disconnected the JJXC-EX sensor to see if the data stream is to high, but also this did not solve the problem. I also refreshed the telemtry in sensor/logging menu a couple of times.

Could it be a faulty Mbar or software problem or to much data stream ?

Thanks!
von Didier

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Ladezeit der Seite: 0.998 Sekunden