Start Twin Turbine

  • mikey
  • mikey's Avatar Offline Autor
  • Gebannt
  • Gebannt
  • Beiträge: 22
  • Dank erhalten: 5

Start Twin Turbine wurde erstellt von mikey

Posted 03 Nov. 2017 00:35 #1
Hello everyone,

I would like to start 2 turbines separately and stop separately, what programming to do to get this?
on a ds24

Regard
Mikaël
von mikey

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • FuniCapi
  • FuniCapi's Avatar Offline
  • Platinum Mitglied
  • Platinum Mitglied
  • Beiträge: 1719
  • Dank erhalten: 839

FuniCapi antwortete auf Start Twin Turbine

Posted 03 Nov. 2017 03:20 #2
This may work with logic switches. Which ECU do you have, or better what is the startup procedure?

Lukas
von FuniCapi

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • mikey
  • mikey's Avatar Offline Autor
  • Gebannt
  • Gebannt
  • Beiträge: 22
  • Dank erhalten: 5

mikey antwortete auf Start Twin Turbine

Posted 03 Nov. 2017 08:45 #3
The ECU are Hornet III project, trim up and stick up 2.
von mikey

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • cpt_volker
  • cpt_volker's Avatar Offline
  • Platinum Mitglied
  • Platinum Mitglied
  • Beiträge: 758
  • Dank erhalten: 312

cpt_volker antwortete auf Start Twin Turbine

Posted 03 Nov. 2017 20:49 #4
Hi Mikey,

i tried to program it. I never did it before, but it seems to work ;-)

I created a Model with One Engine and two extra "Servos" (Turbine 1 and Turbine 2)
Turbine 1 is regulated by P6 with Trim on SC
Turbine 2 is regulated by P5 with Trim on SH
Now You can start, regulate and shutdown the Turbines separately.

Now I made two mixers from Throttle (the digital trim-values for the throttle I set to 0% in both directions) to Turbine 1/2, both activated by Switch SI. The Mixers with a Master Value of 75% and the standard-curve moved to 100% (in 0% / out 100%).
Now, with SI in ON You have both turbines regulated by the throttle. But as I said, it´s not perfect, because it´s a mixer. You still can regulate the turbines with P5/P6, so while flying You should not touch those and keep them in idle-position.
Look at the TEST-Model.
May be one of our Specialists can do it much better ;-)

Regards,
Volker
Last Edit:03 Nov. 2017 20:54 von cpt_volker

Anhänge:

Letzte Änderung: 03 Nov. 2017 20:54 von cpt_volker.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • mikey
  • mikey's Avatar Offline Autor
  • Gebannt
  • Gebannt
  • Beiträge: 22
  • Dank erhalten: 5

mikey antwortete auf Start Twin Turbine

Posted 05 Nov. 2017 00:24 #5
Thanks to you, I'm going to try Volker but I think your programming should work more simply than the Switch Logic version.

Regard
Mikaël
von mikey

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Ladezeit der Seite: 1.072 Sekunden