Willkommen, Gast
Benutzername: Passwort: Angemeldet bleiben:

THEMA:

DS16/gyro401 problem 30 Aug 2020 10:06 #13

  • heliven47
  • heliven47s Avatar Autor
  • Offline
  • Fresh Boarder
  • Fresh Boarder
  • Beiträge: 14
  • Dank erhalten: 1

Hello heliven,
yes, that's the right place!

Ingmar

Hi Ingmar
I can not adjust endpoint in servo setup, only center.
Endpoint I adjust on gyro (LIMIT)
Friendly heliven

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

DS16/gyro401 problem 30 Aug 2020 10:25 #14

  • skyfreak
  • skyfreaks Avatar
  • Offline
  • Platinum Boarder
  • Platinum Boarder
  • Beiträge: 2946
  • Dank erhalten: 1445
I think you have to adjust the endpoints in servo setup as well ...
well let's try it this way

what was the servo limit in the futaba TX?
as you write you make these settings in the gyro
but there must have been a limit in the transmitter as well and I gues it was simply 100% ???

so the transmitter was sending 100 and the rest is done in the gyro.

but 100 on futaba are only 80 on jeti
that way now the gyro instead of getting 100 from futaba it is getting far more
try setting the limits in servo adjustment depending in what was set in the futaba transmitter

rgds
guido
Fliegergruss
GUIDO



_________________________________________________________
Too many dicks on the dance floor.
Too many dicks!​


Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Letzte Änderung: von skyfreak.

DS16/gyro401 problem 30 Aug 2020 10:27 #15

  • IG-Modellbau
  • IG-Modellbaus Avatar
  • Offline
  • Moderator
  • Moderator
  • Beiträge: 3138
  • Dank erhalten: 2244
Hello Heliven,
sure you can, simply adjust "Max positive" to +80% and Max negative" to -80%
In "Subtrim", you have to find the correct % to match to Futaba something around 3%, I think.



Ingmar
Anhänge:

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

DS16/gyro401 problem 30 Aug 2020 17:34 #16

  • heliven47
  • heliven47s Avatar Autor
  • Offline
  • Fresh Boarder
  • Fresh Boarder
  • Beiträge: 14
  • Dank erhalten: 1
Hello to you both.
Now I have trimmed as you recommend.
It does not help, the gyro still can not hold the tail.
When stationary with the engine off, the gyro compensates as it should.
Have tried all values on gain, nothing helps.
Friendly heliven :(
 

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

DS16/gyro401 problem 30 Aug 2020 17:43 #17

  • skyfreak
  • skyfreaks Avatar
  • Offline
  • Platinum Boarder
  • Platinum Boarder
  • Beiträge: 2946
  • Dank erhalten: 1445
do you still have your futaba transmitter?

if so check the min/max values of all channels in uS not prercentages
than recalculate them to jeti values and assign them to the new transmitter
as well check the servo mid positions
and also the servos frequencies in RX setup

I send you a private message
if you want we can check this together eg via whatsapp

rgds
guido
Fliegergruss
GUIDO



_________________________________________________________
Too many dicks on the dance floor.
Too many dicks!​


Bitte Anmelden oder Registrieren um der Konversation beizutreten.

DS16/gyro401 problem 30 Aug 2020 18:43 #18

  • heliven47
  • heliven47s Avatar Autor
  • Offline
  • Fresh Boarder
  • Fresh Boarder
  • Beiträge: 14
  • Dank erhalten: 1

do you still have your futaba transmitter?

if so check the min/max values of all channels in uS not prercentages
than recalculate them to jeti values and assign them to the new transmitter
as well check the servo mid positions
and also the servos frequencies in RX setup

I send you a private message
if you want we can check this together eg via whatsapp

rgds
guido


Thank you very much for the offer Guido, but I am not an expert, so no thanks for the offer.
I have to continue working until the problem is solved.
I also have a Spectrum DX9, in my Trex450 flybarles, could you try with that transmitter?
Friendly heliven

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Ladezeit der Seite: 0.284 Sekunden
Powered by Kunena Forum