Jeti Airspeed Sensor
- TeroS
- Offline Autor
- Platinum Mitglied
- RC-Thoughts
- Beiträge: 527
- Dank erhalten: 370
DIY Jeti Airspeed Sensor is out!
Why not have some fun to do on a rainy night?
News: www.rc-thoughts.com/2017/05/jeti-airspeed-sensor-is-out/
Why not have some fun to do on a rainy night?
News: www.rc-thoughts.com/2017/05/jeti-airspeed-sensor-is-out/
von TeroS
Folgende Benutzer bedankten sich: Sepp62, Olli 80, Aerodeck
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- Aerodeck
- Offline
- Premium Mitglied
- Beiträge: 117
- Dank erhalten: 21
Nice one !
Last Edit:14 Mai 2017 14:16
von Aerodeck
Letzte Änderung: 14 Mai 2017 14:16 von Aerodeck.
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- Eckehard
- Offline
- Senior Mitglied
- Beiträge: 54
- Dank erhalten: 6
Hi Tero,
thanks a lot for sharing your fantastic diy project!
I ordered the MPXV7002DP and will try to use weekend for setting all up.
Regarding the length of the two tubes, I have the following question:
- Is it possible to use longer ones?
- is there a maximum length for both tubes, which should never be exceeded?
- does the length have any negative impact on resolution or accuracy?
Thanks a lot
Eckehard
thanks a lot for sharing your fantastic diy project!
I ordered the MPXV7002DP and will try to use weekend for setting all up.
Regarding the length of the two tubes, I have the following question:
- Is it possible to use longer ones?
- is there a maximum length for both tubes, which should never be exceeded?
- does the length have any negative impact on resolution or accuracy?
Thanks a lot
Eckehard
von Eckehard
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- onki
- Offline
- Platinum Mitglied
- Beiträge: 2286
- Dank erhalten: 791
Hi Eckehard,
check this:
www.sm-modellbau.de/pdf/SM%20Anleitung%2...d-Sensor%20v1.00.pdf
the principle is he same and the hardware might be similar. Tubing lenght does not matter. Theý should be almost the same lenght since is differential pressure.
Best regards
Onki
check this:
www.sm-modellbau.de/pdf/SM%20Anleitung%2...d-Sensor%20v1.00.pdf
the principle is he same and the hardware might be similar. Tubing lenght does not matter. Theý should be almost the same lenght since is differential pressure.
Best regards
Onki
Gruß aus dem Nordschwarzwald
Rainer aka Onki
www.onki.de
gepostet unter Verwendung von 100% recycelter Elektronen.
Rainer aka Onki
www.onki.de
gepostet unter Verwendung von 100% recycelter Elektronen.
Last Edit:20 Juni 2017 23:31
von onki
Letzte Änderung: 20 Juni 2017 23:31 von onki.
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- Eckehard
- Offline
- Senior Mitglied
- Beiträge: 54
- Dank erhalten: 6
Hi Tero, Rainer,
I just want to let you know my diy session last weekend was successfull, my version of sensor "RCT-Airspeed" works fine.
I have tested it in my lab, using a hairdryer (small traveler version)....
Regarding length of tubes...
The total weight of Prandtl pipe, tubes and electronics is so low, that I plan to place all in left wing of a single-engined aircraft, and extend the 3 wire connection to EX port of receiver.....
Thanks a lot to Tero for sharing....
Eckehard
I just want to let you know my diy session last weekend was successfull, my version of sensor "RCT-Airspeed" works fine.
I have tested it in my lab, using a hairdryer (small traveler version)....
Regarding length of tubes...
The total weight of Prandtl pipe, tubes and electronics is so low, that I plan to place all in left wing of a single-engined aircraft, and extend the 3 wire connection to EX port of receiver.....
Thanks a lot to Tero for sharing....
Eckehard
Last Edit:26 Juni 2017 13:22
von Eckehard
Letzte Änderung: 26 Juni 2017 13:22 von Eckehard.
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- Eckehard
- Offline
- Senior Mitglied
- Beiträge: 54
- Dank erhalten: 6
Hi,
today I could test RCT Airspeed Sensor during testflight.
See following picture for installation of sensor
See after flight analysis of recorded log data in Jeti Studio:
Plane: Multiplex PC 6 Turbo Porter
TX: DC16, FW 4.22
Now I know, that my PC6 is a real tractor, speeding up to max. 80km/h during steep approach (from height around 400m down to ground, no flaps set) ,see 5:min20s in diagramm
Thanks again....
Eckehard
today I could test RCT Airspeed Sensor during testflight.
See following picture for installation of sensor
See after flight analysis of recorded log data in Jeti Studio:
Plane: Multiplex PC 6 Turbo Porter
TX: DC16, FW 4.22
Now I know, that my PC6 is a real tractor, speeding up to max. 80km/h during steep approach (from height around 400m down to ground, no flaps set) ,see 5:min20s in diagramm
Thanks again....
Eckehard
von Eckehard
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
Ladezeit der Seite: 1.093 Sekunden