Willkommen, Gast
Benutzername: Passwort: Angemeldet bleiben:
  • Seite:
  • 1

THEMA: REX7 Assist with CB200 and 2x Rsat2 + RC switch - how to bind all this ???

REX7 Assist with CB200 and 2x Rsat2 + RC switch - how to bind all this ??? 09 Sep 2018 12:42 #1

  • MichaelB
  • MichaelBs Avatar Autor
  • Offline
  • Fresh Boarder
  • Fresh Boarder
  • Beiträge: 1
  • Dank erhalten: 0
Dear JETI friends,

I fly my jet with the DC16 transmitter. I bought and installed the Central Box 200 with 2x Rsat2 and the RC switch (the complete set from Hacker). It works beautifully and was fairly easy to install in the jet, binding and programming included, ones I found on YouTube, how to......Bad manuals and bad menu, when you ask my opinion on the 'device manager' menu, in a fantastic transmitter.

So far, so good;

I now bought the REX7 Assist. The idea is to install this REX7 Assist between the CB200 and one of the Rsat2 satelites. I have one satellite installed in the tail of the jet, and one installed in the nose of the jet, with the 4 antennas coming out of the fuselage, due to a lot of carbon fiber inside the fugelage. I have super signals on all 4 antennas during flights, according to the logs.

The manual for the REX7 Assist states, that you need to position the REX7 Assist as close til the CG of the plane, as possible. This is perfectly done on top of the main fuel tank in the jet, with the antenna sticking out of the fuselage right behind the canopy, on the top part of the fuselage, on each side of cause.

My plan is to have BOTH Rsat2 satelittes working, as they are now AND have the REX7 Assist working in between the CB200 and one the Rsat2 satelittes.

So dear JETI friends;
1) Is it possible with the REX7 Assist together with 2x Rsat2 and the CB200 ?
2) AND this without having to start all over again ?
3) and where do we find manuals telling us, how to bind the REX7 Assist along with CB200 and satelittes ?

I can not find one single manual telling me, how to bind the REX7 Assist into a system with central box'es and satelittes, Very frustrating actually with another bad experince on 'lacking manuals for a complex system'.... :-(

I'm totally stock here, so any help would be FANTASTIC :-)

All the best out there....

rgds
Michael Buchreitz
Denmark

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

REX7 Assist with CB200 and 2x Rsat2 + RC switch - how to bind all this ??? 09 Sep 2018 18:45 #2

  • FuniCapi
  • FuniCapis Avatar
  • Offline
  • Gold Boarder
  • Gold Boarder
  • Beiträge: 311
  • Dank erhalten: 99
Check this: https://www.jetiforum.de/index.php/central-box/9488-beschaltung-von-rex-assist-rsat-2-cb200

And this:
http://www.jetimodel.com/en/REX-Assist/Connecting-the-REX-Assist-receiver-in-case-multiple-receivers-are-used/
Just replace the Rsat900 with the RSat2. You have to clone one of the RSats, as you can bind only two receivers in 2-Way-HF-Mode.

Lukas

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Letzte Änderung: von FuniCapi.

REX7 Assist with CB200 and 2x Rsat2 + RC switch - how to bind all this ??? 13 Sep 2018 21:07 #3

  • Ceeray
  • Ceerays Avatar
  • Offline
  • Fresh Boarder
  • Fresh Boarder
  • Beiträge: 3
  • Dank erhalten: 0
I got the same problem, CB200+REX6A+ RSAT2.

Tried the routing mentioned in the picture.

rx1: REX6A EXBUS E1 to CB200. E2 PPM input.
rx2: RSat2 EXBUS to CB200 AND PPM out to REX6A PPM input (Rsat2 has an option to choose both at the same time)
I get Morse error "E" but disabled it.

Now I tried following:
1- disconnected signal wire only from CBrx1- REX6A. Servos worked.
2- disconnected power only from REX6A . Servos worked as the power was rerouted from RSat2 to REX6A via PPM cable.
3- disconnected power also from above. Servos worked. RSat2 must have taken over.
4 - disconnected REX6A - Rsat2 PPM cable. Servos worked.
5. -disconnected RSat2 from PPM, no change as RX1 is primary. etc..

So it looks it works. Also , are Q1/Q2 signals now correct is Q1 for rx1 and Q2 for rx2 port?

This is a good workaround.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Letzte Änderung: von Ceeray.
  • Seite:
  • 1
Ladezeit der Seite: 0.139 Sekunden
Powered by Kunena Forum